Vari lite vl1000 manual




















Page Chapter 1. Thru, and AC Power connections. In this case, the lamp power input cable is already connectorized for use with this unit. The following illustration shows the external arc ballast components.

Please order by Vari-Lite part number. Page Chapter 2. It includes connecting power and data, along with instructions for powering up the luminaire for the first time and addressing it within your system. The lamp power input cable is already connectorized for use with this unit. Note: There is no provision for lengthening the cable. The ballast must be placed within 40 inches 1m of the luminaire. When purchasing or constructing data cables, it is important that not only the correct cable type be used, but also quality cable to ensure a reliable DMX system.

Any quality EIA, twisted pair, ohm, shielded cable will also work. Signal reflections may cancel out the signal at certain line lengths, resulting in errors. Touching lamp glass with bare fingers will leave oil and may cause the lamp to explode or reduce lamp life. At backcap, flip two bail clamps outward Figure Step 4. Flip two base clamps outward away from socket.

Step 5. Grip lamp by base and firmly install in socket. Do not touch lamp with bare fingers. The frame holder is designed to fit a standard 8-inch gel frame or top hat.

To remove and replace frame or top hat: Step 1. The pan tube base provides two mounting holes for attaching truss hooks or other mounting hardware as required. Lift luminaire into mounting position. Step 2. Secure in place with truss hooks. Ensure truss hook hardware that locks hook in place e.

In order for the lamp cable to be connected, the ballast must be placed within 40 inches 1m. Lift ballast into mounting position. Secure in place with truss hook. Note: This maximum limit applies to the luminaire "daisy chain" only. Your system or console may require fewer luminaires on a single data link path. This procedure will usually happen prior to delivery. However, in the event that it has not been done or if the Main Controller Board has been replaced, it will be necessary.

Note: Refer to Chapter 4: Menu System for detailed instructions on menu functions. CAUTION: Before applying power, be sure the luminaire is hung or positioned so that the head and yoke can move freely without restriction. This address will be retained even if the power is removed. Note: Refer to your console operating instructions for specific information regarding its addressing requirements. Page Chapter 3. Regardless, this channel must be included for both profiles.

These must be executed with zero time transition or with timing disabled. Discrete values must be used; not manual controls such as faders or encoders see chart below for values. It shows only the number of channels used for the given luminaire model in bit enhanced mode. We provide three timing channels, one for Focus Pan and Tilt , one for color parameters and one for beam parameters. Set console timing or cue fade time for parameters and timing channels to zero seconds.

Store cue. Note: Avoid changing timing channel values in a fading cue. This can cause unexpected behavior in the luminaire as the timing channel value is updated over time. Timing channel values and the final destination of the parameters affected by the timing channel should always be sent in a zero count.

The VLDownload. Install VLDownload. Download All button is the equivalent of executing all of the specific Choice 5 software version buttons described above.

Verify software version at luminaire: Step 1. Page Transferring Software From Luminaire To Luminaire 24 , however a maximum of 32 luminaires can be updated at once. The transfer process can be used to download an earlier or later version of the VL Luminaire Software to other connected VL luminaires. The software is the same for all VL models. Once download is complete, luminaire will automatically recalibrate. Once recalibration is complete, luminaire is ready for operation with its new software version.

Cooling: Free convection cooling when hung. Floor mounted units and extreme ambient temperatures activate a low-noise, forced-air cooling system. Control: Completely compatible with a wide variety of DMX consoles. Spacing: Full range of motion on Hangs as close as Weight: 70 lbs 32 kg. Source Four technology provides a clean white beam for unequaled imaging, Read more….

A flashy little unit that packs a powerful punch, the Dataflash AF features technical advances that place it in a class by itself. This individually addressable strobe can be used in a variety of settings Read more….

Categories: Lighting Moving Lights.



0コメント

  • 1000 / 1000